Used 450 gallon 316L Stainless Steel Pressure Tank. Manufactured by Groen. Vertical. Approximate 30" diameter x 144" straight side, bolt on dished top and bottom. Internal rated 45 psi & Full Vacuum at 300 degrees F. Top entering Cleveland agitator, model APD2M-5, serial# 12288-02. Need to verify shaft and blades, driven by a 7.5hp, 3/60/230/460 volt, 1760 rpm motor. Side lug mounts. National Board# 20726, built 1963, altered in 2007.

Used Intellishare Environmental Thermal Oxidizer. Approximate maximum air flow capacity 0 to 1700 SCFM, average inlet temperature 40-115 degrees F., minimum thermal operating temperature 1400 degrees F., average operating temperature 1650 degrees F., maximum thermal operating temperature 1800 degrees F., chamber residence time (1) second. Consists of: (1) 316 stainless steel chamber, approximate 20' tall stack, thermal oxidizer 5,150,000 BTU burner, (1) Robinson combustion air blower, flow approximate 1260 SCFM, (2) New York blowers, each air flow approximate 1800 SCFM, (1) 316 stainless steel knockout tank, (1) 316 stainless steel HEPA filter, control panel with Allen-Bradley PowerFlex drives, DigiTrace heat tracing controllers, Allen-Bradley PLC, and an Allen-Bradley PanelView Plus 1500.

Used- Von Roll RPE Belt Filter Press, Model RPE2000L. Approximate 78” wide belt driven by a 5hp, 3/60/230/460 volt, 1680 rpm gear motor. Includes a stainless steel feed tank with screw type agitator driven by a 2hp variable speed motor, dual knife discharge scrapers, bottom drip pan and a panel. Serial# 0066, commission# 714301, built 1985.

Used Twin Screw Conveyor Feeder. (2) Approximate 18" diameter x 120" long x 8" pitch screws. 18" Diameter top end feed with a bolt on hopper, end bottom discharge. Includes a reducer, no motor.

Used 1.4 MGPY Fermentation Plant with Real Estate built in 2009. Available with real estate or without real estate as plant/equipment only. Consists of used 1.4 M gallon/year fermentation plant (demonstration plant) and pilot plant. Started in 2009, finally shut down in 2015. Originally designed to produce lignocellulosic ethanol (LCE). Feedstocks including: (1) common sugar cane, (2) purpose grown energy cane, (3) sorghum, (4) bagasse. Offering includes the following process sections: Feedstock handling, Feedstock transfer, Feedstock preparation, Hydrolysis, Liquefaction, Yeast and enzyme propagation, C5, C6 co-fermentation, Ethanol recovery. Plant includes a pilot plant used to develop LCE technology.

UNUSED - FRC Systems PWL Series DAF Low-Built Dissolved Air Flotation System, Model PWL-100, Stainless Steel. Flow rate up to 430 gallons per minute, free area 205 square feet. Tank approximate 79" wide x 36 long x 42" deep, coned bottom. Includes skimmer flights, driven by a 1/2 hp, 3/60/230/460 volt, 1735 rpm XP gear motor, ratio 217.41 to 1, end float discharge pan, whitewater dispersion manifold, air dissolving tube, sludge discharge screw conveyor, driven by a 1/2 hp, 3/60/230/460 volt, 1735 rpm XP gear motor, ratio 217.41 to 1. Serial# 12140091-A. Built 2012. Includes FRC Systems F Series Flocculator, Model F4SS-4/6-2M, Stainless Steel. Flow rate 119-173 gallons per minute. 4" Inlet, 6" outlet. Mounted on a stainless steel frame. Serial# 12140091-A. Includes a control panel with Allen-Bradley PowerFlex drives and Allen-Bradley Logix 5561 controller. Built 2012.

Unused FRC Systems F Series Flocculator. Model F4SS-4/6-2M, Stainless Steel. Flow rate 119-173 gallons per minute. 4” Inlet, 6” outlet. Mounted on a stainless steel frame. Serial# 12140091-A. Built 2012.

Thib's Machine & Welding Column, Stainless Steel. (6) Bolt together sections, approximate 16” diameter x 220” tall. Internal rated 14.9 psi at 250 degrees F. Built 2007. Includes a Goulds pump, model 1SS1H5K0, driven by a 3hp, 3/60/230-230/460 volt, 3450 rpm motor.

Used KEMCO Krueger Engineering Single Pass Vertical Shell & Tube Heat Exchanger, Approximate 27.5 Square Feet. Carbon steel shell rated 100 psi at 250 degrees F., (24) 3/4" Diameter x 72" long 316 stainless steel tubes rated 50 psi & Full Vacuum at 400 degrees F. (2) 316L Stainless steel tubesheets, (1) SA 234 Chrome Moly Alloy head. Openings shell (2) 2", openings tubes (2) 2". Side lug mounts. National Board# 1431, serial# 85-102, built 1985.

Used- Northland Stainless Reactor, 200 Gallon, 316 Stainless Steel, Vertical. 42" Diameter x 30" straight side, dished top and bottom. Internal rated Full Vacuum and 20 psi at 260 degree F, carbon steel jacket rated Full Vacuum and 20 psi at 260 degrees F. Openings top (7) 2" tri-clamp, 3", 5" sight glass, 15" man way with a 5" sight glass in cover. 2" Tri-clamp center bottom outlet. Mounted on 4 stainless steel legs. National Board #34, serial# 76448-2, built 1976.

Used Crepaco Reactor, 64 Gallon, 316L Stainless Steel, Vertical. 30" Diameter x 18" straight side, dished top and bottom. Internal rated 25 psi at 300 degrees F. 316L Stainless steel dimple jacket rated 75 psi at 300 degrees F. Top entering Lightnin agitator, model X5S33, serial# 5630, approximate 1” diameter shaft with a 3 blade turbine, driven by a 1/2hp, 3/60/230/460 volt, 1725 rpm motor. Openings top (3) 1-1/2" tri-clamp, 3" tri-clamp. 2" Center bottom outlet. Mounted on 4 stainless steel legs. National Board# 5682, serial# D-2027, built 1984.

Used Northland Stainless Reactor, 300 Gallon, 316L Stainless Steel, Vertical. 48" Diameter x 36" straight side dished top and bottom. Internal rated Full Vacuum and 50 psi at 365 degrees F, 304L stainless steel dimple jacket rated 150 psi at 365 degrees F. Off center top entering Lightnin agitator, model XDDS-30, serial# 83/186312, approximate 1” diameter shaft with a 3 blade turbine, driven by a 1 HP, 3/60/230/230/460 volt, 1140 rpm motor. Openings top (2) 2" tri-clamp, (2) 2-1/2" tri-clamp, 3" tri-clamp, 6", 5", 5" sight glass, 15" man way with a 5" sight glass in cover. 2" Tri-clamp center bottom outlet. Mounted on 3 stainless steel legs. National Board# 583, serial# 873522-1, built 1987.

Used- Hyundai HL740-9 Wheel Loader

Used- Kawasaki Mule

Used Mueller Reactor, 33 Gallon (125 Liter), 316L Stainless Steel, Vertical. 18" Diameter x 31" straight side flat bolt on top, dished bottom. Internal rated Full Vacuum and 45 psi at 300 degrees F, 304 stainless steel jacket rated Full Vacuum and 45 psi at 300 degrees F. Top entering Lightnin agitator, model EV5L33M, serial# R06386310-01, approximate 1/2” diameter shaft with a 3 blade turbine, driven by a 0.33hp, 90 volt, 1800 rpm DC motor with controller. 3 stainless steel legs. National Board# 12482, serial# P22410-1, built 1987.

Used Lee Industries Reactor, 300 Gallon, Model 300 DBT, 317L Stainless Steel, Vertical. 48" Diameter x 40" straight side, dished bolt-on top, dish bottom. Internal rated 50 psi at -20 to 180 degrees F and designed for vacuum service, 304 stainless steel jacket rated 15 psi at -20 to 338 degrees F. Top entering Lightnin agitator, model 118-REC-1.5.2, serial# 681675, ratio 17.40 to 1, output rpm 100, approximate 2" diameter tapered shaft with a 3 blade turbine, driven by a 1hp, 3/60/230/460 volt, 1764 rpm motor. 3 Side wall baffles. Openings top 12", (6) 2", (5) 3", (2) 1", 8", bottom 2 approximate 2", 4" center. Mounted on 4 stainless steel legs. National Board# 5099, serial# B5526A, built 1991.

Used New Brunswick Scientific BioFlo Pro 500L Fermentor System, Approximate 132 Gallon, 316L Stainless Steel. Vessel approximate 24” diameter x 60” straight side, dished clamp on top, dish bottom. Internal rated 40 psi at -20 to 300 degrees F., jacket rated 50 psi at -20 to 300 degrees F. Bottom entering agitator, approximate 2” diameter shaft with (3) 6 blade disc turbines, driven by a 5hp, 3/60/230/460 volt, 300-3600 rpm gear motor, ratio 8.91 to 1, sidewall baffles. Includes a piping module with valves, and a control panel with a Control Techniques Commander SE drive and an Automation Direct EZ-T10C-FS operator panel. Vessel National Board# 2083, serial# 2287, built 2002. System MFG# R1290-1004-001, serial# R300544099.

Used Fermentor, Approximate 130 Gallon, Stainless Steel. Vessel approximate 30” diameter x 42” straight side, dished top and bottom. Internal not rated, jacket not rated. Bottom entering agitator, approximate 2” diameter shaft with (3) 6 blade disc turbines, driven by a 7.5hp, 3/60/230/460 volt, 1770 rpm motor. Sidewall baffles. Mounted on a carbon steel frame with motorized vessel lift. No manufacturers tag.

Used Hatton Enterprises Acid Hydrolysis Digester System. Consisting of: (1) Approximate 12” diameter x 168” long SB-551 Zirconium chamber, rated 400 psi at -20 to 447 degrees F. Driven by a 5hp motor thru a reducer. Includes a top feeder driven by a 10hp motor thru a reducer. Certified by Astro Cosmos, National Board# 1891, serial# 69841, built 1999.

Used Approx 32.6 Cu Ft Groen Continuous Screw Blender, Model CSB-16180, 316 Stainless Steel. Approximate 16-3/4" wide x 14' long x 20" deep stainless steel jacketed trough rated 120 psi at 353 degrees F. Approximate 4-1/4" diameter 304 stainless steel shaft with a single 304 stainless steel ribbon 2" wide x 3/16" thick. Partial top cover sections, 12" x 17" end bottom outlet. Driven by a 2hp gear motor. National Board# 140046, serial# 01801-1, built 1998.

Used Vincent Corporation CP Horizontal Screw Press, Model CP-6, Stainless Steel. Approximate capacity 300-1000 pounds per hour, approximate 6” diameter x 32” long screw, approximate 20 rpm. Driven by a 5hp, 3/60/208-230/460 volt, 1740 rpm motor thru a reducer, ratio 91.81 to 1. Includes a perforated sheet screen pair and a wedge wire screen set. Serial# 7134-A.

Used Vincent Corporation CP Horizontal Screw Press, Model CP-6, Stainless Steel. Approximate capacity 300-1000 pounds per hour, approximate 6” diameter x 32” long screw, approximate 20 rpm. Driven by a 5hp, 3/60/208-230/460 volt, 1740 rpm motor thru a reducer, ratio 91.81 to 1. Includes a perforated sheet screen pair and a wedge wire screen set. Serial# 7134-B.

Used Vincent Corporation CP Horizontal Screw Press, Model CP-6, Stainless Steel. Approximate capacity 300-1000 pounds per hour, approximate 6” diameter x 32” long screw, approximate 20 rpm. Driven by a 5hp, 3/60/208-230/460 volt, 1740 rpm motor thru a reducer, ratio 91.81 to 1. Includes a perforated sheet screen pair and a wedge wire screen set. Serial# 7134-C.

Used Clean In Place CIP System Consisting Of: (1) Approximate 75 gallon stainless steel tank, (1) Enerquip shell & tube heat exchanger, shell and tubes rated 150 psi at -20 to 375 degrees F., National Board# 3943, serial# 5363, built 2001, (1) Fristam centrifugal pump, model FPX731-170, stainless steel, serial# FPX73101698. Driven by a 1.5hp, 3/60/230/460 volt, 1740 rpm motor, (1) stainless steel control cabinet only, no controls. Mounted on a stainless steel frame.

Used Tank, Approximate 600 Gallon, Stainless Steel, Vertical. Approximate 54” diameter x 58” straight side, flat bolt on top, flat bottom. Top manway, off center bottom outlet. Mounted on 4 stainless steel legs. No manufacturers tag.

Used Tank, Approximate 900 Gallon, Stainless Steel, Vertical. Approximate 60” diameter x 72” straight side, flat top, dished bottom. Top manway, center bottom outlet. Mounted on 4 carbon steel legs. No manufacturers tag.

Used Clean In Place CIP System Consisting Of: (1) Approximate 150 gallon stainless steel tank, (1) shell & tube heat exchanger, (1) Crepaco centrifugal pump, model 18V-85, stainless steel, serial# 17. Driven by a 20hp, 3/60/230/460 volt, 3510 rpm motor. Mounted on a stainless steel frame.

Used Mueller Kettle, Approximate 1500 Gallon, Model PCPC-12,000#, 316L Stainless Steel, Vertical. Approximate 78" Diameter x 78" straight side, dished top, coned bottom. Overall Height: 14'. Jacket rated 150 psi. Top entering Chemineer agitator, model 2HTN-2, serial# 1-99324-3, output rpm 37, approximate 2" diameter shaft with (2) 4 blade turbines, driven by a 3hp, 3/60/208-230/460 volt, 1720 rpm motor. Side wall baffles. Top man way, center bottom outlet. Mounted on 4 stainless steel legs. Serial# 82398.

Used APV Crepaco SS Tank. Approximate 1500 Gallon, Stainless Steel, Vertical. Approximate 84" Diameter x 54" straight side, dished top, coned bottom. Internal rated 15 psi @200F. Top entering agitator, approximate 2" diameter shaft with a 4 blade turbine, driven by a 3/4hp, 3/60/230/460 volt, 1700 rpm gear motor, ratio 135.28 to 1. Side wall baffles. Top man way, center bottom outlet. Mounted on 3 stainless steel legs. Serial# F-9838.

Used Cloth Belt Washer, Approximate 12” wide x 13’ long. Belt driven by a 15hp motor thru a Falk reducer, ratio 70.51 to 1. Includes (7) wash manifolds, water holding tank with pumps, (1) Hydra-Cell D10SKS 1.5hp pump, (1) Durco MK3 3hp pump, (1) New York 10hp pressure blower, (1) control panel with drives. Mounted on a carbon steel frame. No manufacturers tag.

Used Southwest Tank & Treater Tank, 5000 Gallon, Stainless Steel, Vertical. Approximate 108" Diameter x 136" straight side, flat top, dish bottom. Top entering Jensen agitator, model 1105-5/100, serial# FG-149, output rpm 100, approximate 2" diameter shaft with a 4 blade turbine, driven by a 5hp, 3/60/230/460 volt, 1750 rpm motor. Top man way, center bottom outlet. Mounted on 4 carbon steel legs. Serial# 10680, built 1985.

Used Tank, Approximate 8500 Gallon, Stainless Steel, Vertical. Approximate 144" Diameter x 120" straight side, coned top, flat bottom. Side man way and side bottom outlet. No manufacturers tag.

Used TPI Industrial Tank, Approximate 1500 Gallon, Stainless Steel, Vertical. Approximate 72" Diameter x 80" straight side, dished top and bottom. Sidewall baffles, top man way, center bottom outlet. Mounted on 4 carbon steel legs.

Used PEMCO Process Engineering & Machine Tank, Approximate 1000 Gallon, Stainless Steel, Vertical. Approximate 72" Diameter x 60" straight side flat bolt on top, coned bottom. Top entering Lightnin agitator, model 119-RELB-22, serial# 596362, ratio 20.9 to 1, output rpm 84, approximate 2” diameter shaft with a 4 blade disc turbine, driven by a 2hp, 3/60/230/460 volt, 1160 rpm XP motor. Bottom internal coil (no rating), sidewall baffles, top man way, center bottom outlet. Mounted on 4 carbon steel legs. Serial# 1241, built 1959.

Used Tank, Approximate 1000 Gallon, Stainless Steel, Vertical. Approximate 64" Diameter x 86" straight side, dish top, coned bottom. Top entering Lightnin agitator, model 81-S-1.5, serial# 752361, ratio 21.1 to 1, output rpm 56, approximate 2” diameter shaft with a 4 blade turbine, driven by a 1.5 HP, 3/60/230/460 volt, 1170 rpm motor. Sidewall baffles, side man way, center bottom outlet. Mounted on 4 carbon steel legs. No manufacturers tag. Overall height w/legs and motor drive - 18' 1".

Used B. Nolte & Sons Reactor, 1200 Gallon, 304 Stainless Steel, Vertical. Approximate 66" Diameter x 72" straight side, dished top, jacketed coned bottom. Internal rated Full Vacuum & 15 psi at 400 degrees F, 304 stainless steel dimple jacket rated 100 psi at 400 degrees F. Approximate 2" diameter shaft with (2) 4 blade turbines, no drive. Side wall baffles, top man way, center bottom outlet. Mounted on 4 carbon steel legs. National Board# 1870, serial# 1870, built 1979.

Used NOV Brandt National Oilwell Varco King Cobra Shaker, Model 1099509618, Carbon Steel. (4) 49-1/4” wide x 25” long x 1” thick screen sections, screening area 33.4 square feet. Driven by (2) 2.5hp, 3/60/220-240/440-480 volt, 1800 rpm vibratory motors. Work order# 205609, part# 10995-0134, built 2009.

Used- Alfa Laval SG2-500 Solid Bowl Decanter Centrifuge. Stainless steel construction (product contact areas). Maximum bowl speed 3650 rpm, 360 degree solids discharge ports with replaceable sintered tungsten carbide wear protection inserts, moon liquid dam plate, 3.5 kNm DD gearbox 52:1 ratio, feed pipe, base, casing, 75hp main drive motor 460/3/60, 15hp back drive. Includes an operators control station and a main control panel with ABB drives.

Used- FKC Screw Press, Model SHX-800X6000L, 316L Stainless Steel. Approximate capacity 65-165 kg/hr, depending on product, maximum pressure 0.7 MPa. Approximate 800mm diameter x 6000mm long screw. Top end feed, bottom end discharge. (4) external screen assembly spray bars, bottom drip pan. Driven by a 30hp, 3/60/460 volt, 1175 rpm motor thru a reducer, ratio 319 to 1. Mounted on an I-beam carbon steel frame. Serial# M-2448, built 2007.

Used- FKC Screw Press, Model SHX-800X6000L, 316L Stainless Steel. Approximate capacity 65-165 kg/hr, depending on product, maximum pressure 0.7 MPa. Approximate 800mm diameter x 6000mm long screw. Top end feed, bottom end discharge. (4) external screen assembly spray bars, bottom drip pan. Driven by a 30hp, 3/60/460 volt, 1175 rpm motor thru a reducer, ratio 319 to 1. Mounted on an I-beam carbon steel frame. Serial# M-2428, built 2007.

Unused- Flowserve MK3 US Primer. Centrifugal Pump, Stainless Steel. Size 1K1.5X1.5US820P. Driven by a 2hp, 3/60/460 volt, 1755 rpm motor. Serial# 1088665CHP001A, built 2012.

Used Parker Fulflo Multiple Bag SB Filter Vessel, Model 36429-4LSB92-6FK1, 304L Stainless Steel. Approximate maximum flow 1440 gallons per minute. Appproximate 32" diameter x 54" tall. Internal rated 180 psi at 400 degrees F. Certified by Lagrange Products, National Board# 484324, built 2010.

Used Flexicon BFH-C-X Half Frame Bulk Bag Discharger Frame. Includes (2) air operated bag holders, (1) Tele-Tube telescoping tube, (1) Salina Vortex slide valve, (1) Flexicon agitated hopper, (1) ball valve. Mounted on a carbon steel frame rated for 3200#. Serial# 56574, built 2007.

Used Flexicon BFH-C-X Half Frame. Includes (2) air operated bag holders, (1) Tele-Tube telescoping tube, (1) Salina Vortex slide valve, (1) Flexicon agitated hopper, (1) ball valve. Mounted on a carbon steel frame rated for 3200#. Serial# 56574, built 2007.

Used- Flexicon BFH-C-X Half Frame. Includes (2) air operated bag holders, (1) Tele-Tube telescoping tube, (1) Salina Vortex slide valve, (1) Flexicon hopper, (1) ball valve. Mounted on a carbon steel frame rated for 3200#. Serial# 56574, built 2007.

Used Flexicon BFH-C-X Half Frame. Includes (2) air operated bag holders, (1) Tele-Tube telescoping tube, (1) Salina Vortex slide valve, (1) Flexicon agitated hopper, (1) ball valve. Mounted on a carbon steel frame rated for 3200#. Serial# 56574, built 2007.

Used Flexicon BFH-C-X Half Frame. Includes (2) air operated bag holders, (1) Tele-Tube telescoping tube, (1) Salina Vortex slide valve, (1) Flexicon hopper, (1) ball valve. Mounted on a carbon steel frame rated for 3200#. Serial# 56574, built 2007.

Used Steel-Pro Pressure Tank, Approximate 6300 Gallons, 304L Stainless Steel, Vertical. Approximate 76” diameter x 318” straight side, dished top and bottom. Internal rated 30/-10 psi at -20 to 300 degrees F. Top entering Cleveland agitator, model BHD2M-5, serial# 12165-04, approximate 4” diameter shaft with multiple turbines and a mechanical seal, driven by a 40hp, 3/60/460 volt, 1775 rpm motor. Side wall baffles, top and side bottom man way, center bottom outlet. Mounted on 4 carbon steel legs. National Board# 1361, serial# 17977C, built 2007.

Used Steel-Pro Pressure Tank, Approximate 6300 Gallons, 304L Stainless Steel, Vertical. Approximate 74” diameter x 318” straight side, dished top and bottom. Internal rated 30/-10 psi at -20 to 300 degrees F. Top entering Cleveland agitator, model BHD2M-5, serial# 12165-01, approximate 4” diameter shaft with multiple turbines and a mechanical seal, driven by a 40hp, 3/60/460 volt, 1775 rpm motor. Side wall baffles, top and side bottom man way, center bottom outlet. Mounted on 4 carbon steel legs. National Board# 1360, serial# 17977B, built 2007.

Used Steel-Pro Pressure Tank, Approximate 6300 Gallons, 304L Stainless Steel, Vertical. Approximate 74” diameter x 318” straight side, dished top and bottom. Internal rated 30/-10 psi at -20 to 300 degrees F. Top entering Cleveland agitator, model BHD2M-5, serial# 12165-02, approximate 4” diameter shaft with multiple turbines and a mechanical seal, driven by a 40hp, 3/60/460 volt, 1775 rpm motor. Side wall baffles, top and side bottom man way, center bottom outlet. Mounted on 4 carbon steel legs. National Board# 1359, serial# 17977A, built 2007.