Recent Purchases and Listings

Used 20" Diameter decanter centrifuge. Manufactured by Alfa Laval. Model NX5152. AL 111 2327 (Lean Duplex Stainless Steel) 510mmm D x 2247mm L bowl. 3250 RPM. Liquid outler 2-phase; open; (6) Standard Plate dams. Solids Discharge 360 type w (8) Openings w Tungsten Carbide liners. Max Solids Density 1.5 kg/dm. 40Hp main motor. 30 HP back drive motor. Serial #5026017. Built 2015.

Unused 200000 lb/hr water tube boiler. Manufactured by Rentech Boiler Systems Inc. Model Waterwall “O” Type HRSG. MAWP 450PSIG@550F. Tubes 450SPIG@700F. Heat Surface 52019 Sq Ft. Built 2024.

Used 36"W x 16L 316L stainless steel fluid bed dryer. Manufactured by GEA Barr-Rosen. Capacity 774 lb/hr. Design rate 4,244 lb.hr with infeed moisture at 20% by weight, final product output at 3% by weight. Duct heater/burner and control panel. Model DH-65-4-0-NPO. Natural gas. Maximum input 4,000,000 BTU / hr. Fans, blowers, cyclone. (4) Sifter Screen units. Ducting included. Past use Corn Germ Drying.

Used 70" Diameter 304L Stainless Steel Rotary Steam Dryer. Manufactured by Drying Solutions Inc. Drum: 580"OAL. Rated at 1500 lbs/hr capacity with co-current single-pass superheated steam. Conveying air feed 1973 acfm @ 266F - 288F. (Max inlet temp 680F). Natural gas fired burner with controls and fire-eye, Blower, belt drive. Rated at 7.3 MMBTU/hr. Cyclone and vertical condenser. Drag conveyer and 3 screw conveyors. Electrical 200 amp service 460v. Starters and VFD's are located in the control cabinet. (4) VFDs. 60HP blower, 60HP conveying fan, 40 HP burner, 40HP drum. All controls including PLC and touch screen HMI built into panel. Built 2009. Last use soybean meal.

Unused 7000 gallon Carbon steel horizontal tank. Built by Modern Welding Company. 9' OD x 18' long T/T. Carbon steel shell with Carboline Plasite 3070L internal lining. Horizontal on carbon steel welded saddles. Internal rated atmospheric at ambient temp. Dished Ends. 2" end bottom outlet. Never had acid put in the tank. 2 tanks available.

Used 26500 gallon 304 Stainless Steel vertical tank. Manufactured by Bendel. 15'D x 21' straight side. Rated ATM @ 100F. Specific Gravity 1.0. Slight cone top, dish bottom. 24" top manway, 24" side manway, (6) 8" studded pads, (1) 4" flanged, 4" bottom drain. Insulated with sheathing. (4) leg mounted. Serial #S1606 2/3. Built 1995. Past use Pure Water.

Used 8 MMBTU/hr Hot Oil boiler/Thermal Fluid heater. Manufactured by Fulton. Model FT-0800C. Rated 8000000 BTU/output. 9195000 input. 700 sq ft heating area. 200 gallon capacity (thermal fluid). 500 GPM. 2"D heating coil. 4-pass. Rated 200PSI @ 650F. Includes pump skid, deaerator/expansion/thermal buffer tank. Serial #7649C. National Board #8831. Built 2014.

Used 24" x 20' 316L Stainless Steel Dual Screw Holoflite dryer. Manufactured by Anderson Dahlen. Screw and Jacket rated 100PSI/FV@350F. 3HP motor with chain drive. Serial #327437C-1. National Board #344. Built 2015.

Used 25 HP Premier SuperMill media mill. Model HM-15VSD. Carbon steel jacketed chamber and disks. 16.5 liter gross capacity. 15 liter working capacity chamber. Mechanical seal with seal pot. 25 hp 460 volt xp motor. .75 hp xp on board feed pump. On-board xp controls. Serial# HM15-90614-92-001. Built 1996.

Used 4800 gallon 304 stainless steel tank. Manufactured by Alloy Fab. ATM @140F. Cone top, flat bottom. 5600lb. Serial #1-165A. Built 1991. Past use Toluene filtrite tank.

Used 40 gallon stainless steel agitated mix tilt kettle. (3) Electric heaters below jacket bowl. Interior bowl measures 23-1/4” diameter X 17” deep. 1HP motor with Sweep agitator with Teflon scrapers (one missing). Control box. A-Frame stand mounted.

Used Westfalia NA-7-06-076 Stainless steel Desludger/Nozzle Disc Centrifuge. Max bowl speed 8510 rpm. Clarifier design (liquid/solids separation). Centripetal pump liquid discharge. Flanged mounted drive motor 7.5hp 230/460/3/60 volt drive motor. Cart Mounted. Control panel with A/B microview, A/B micrologix 1000 PLC.

Used Gaulin Model 15M-8TBA Laboratory Homogenizer. 8000 PSI Ball valve cylinder with Max pressure 10000 PSI. 15 GPH. 2-stage manual valve assembly. 2 HP motor. Painted frame. Serial #6663201.

Used 20 Gallon Stainless Steel Self-Contained Electric Jacketed Tilt Kettle. Manufactured by Market Forge Model FT-20CE. Dimensions 21 ID X 19 deep. Jacket Rated 50 PSI @ 98F. Stainless steel base with casters. Electrical specs: 3/60/208 Volt. Top lid. Serial #74058-2cc-0801 (5148-1cc-0369). National Board #51985. CRN #OH7902-58/D4945.6.

Used 7250 gallon vertical carbon steel pressure vessel. Manufactured by CE Natco. MAWP 500PSI @ 100F. 78"ID x 25'T/T. Cone bottom, dome top. Skirt mounted. Serial #T-7406001-01. Built 1980.

Used 458 Ton Stainless Steel Cooling towers. Manufactured by Baltimore Air Cooling. Model 3473C-MM. Series 3000. Single cell units. 25 HP fans. 118,870 CFM. 10900 lb. 21ft6.5in L x 10ft 10.625in W x 9ft 11.75in H. (Qty 4 available)

Used 25000 gallon 304 Stainless Steel jacketed vertical tank. Manufactured by DCI (Dairy Craft Inc). 12'Dia x 31' Straight Side. Dimple jacket. Slope bottom, dome top. Serial #76J2670-1. Built 1976. Past use dairy. Qty 2 available.

Used Universal Pack Srl Model Gamma G3C-DBR Pouch-in-Pouch Machine. 90 pouch per minute. 3 x 120mm flat-filter into 150mm x 170mm foil package. Product weight .55oz-1.0oz. Nitrogen flush. Includes dosing unit, product hopper with horizontal pre-infeed auger. Sachet former with heat-sealer - Left to Right film reel holder. Front and foil control panels. 480/60/3 23.8A. Electric cabinet. Serial #21A03 US. Built 2021. Weight 4000 kg.

Unused 693 square foot Shell and Tube Heat Exchanger. Bulit by Gaspar Inc. 26” diameter X 6’ 5” face to face length. Carbon steel shell rated 614 PSI @ -20 to 450F. (551) 3/4” SA179 carbon steel tubes rated 611 PSI @ -20 to 450F. 12” Process, 6” Service nozzles. Insulated. National Board# 2830. Serial #37318-2. Built 2010.

Unused 89520 Litre (23648 gallons) 316L Stainless Steel Reactor. Manufactured by ZVU Strojirny. Internal 6/FV barg @ 170C. Jacket 10/FV barg @ 125C. Half pipe jacket on bottom half of shell and bottom head. Dished Top and bottom. 4100mm ID x 5750mm TL-TL. (2) 762mm top manways with davit. (4) Lug mounted. Serial #465. Built in 2021. Stored under Nitrogen purge.

Unused 89520 Litre (23648 gallons) 316L Stainless Steel Reactor. Fabricated by ZVU Strojirny. Internal 6/FV barg @ 170C. Jacket 10/FV barg @ 125C. Half pipe jacket on bottom half of shell and bottom head. Dished Top and bottom. 4100mm ID x 5750mm TL-TL. (2) 762mm top manways with davit. (4) Lug mounted. Serial #464. Built in 2021. Stored under Nitrogen purge.

Unused 89520 Litre (23648 gallons) 316L Stainless Steel Reactor. Manufactured by ZVU Strojirny. Internal 6/FV barg @ 170C. Jacket 10/FV barg @ 125C. Half pipe jacket on bottom half of shell and bottom head. Dished Top and bottom. 4100mm ID x 5750mm TL-TL. (2) 762mm top manways with davit. (4) Lug mounted. Serial #460. Built in 2021. Stored under Nitrogen purge.

Unused 89520 Litre (23648 gallons) 316L Stainless Steel Reactor. Built by ZVU Strojirny. Internal 6/FV barg @ 170C. Jacket 10/FV barg @ 125C. Half pipe jacket on bottom half of shell and bottom head. Dished Top and bottom. 4100mm ID x 5750mm TL-TL. (2) 762mm top manways with davit. (4) Lug mounted. Serial #459. Built in 2021. Stored under Nitrogen purge.

Unused 89520 Litre (23648 gallon) 316L Stainless Steel Reactor. Manufactured by ZVU Strojirny. Internal 6/FV barg @ 170C. Jacket 10/FV barg @ 125C. Half pipe jacket on bottom half of shell and bottom head. Dished Top and bottom. 4100mm ID x 5750mm TL-TL. (2) 762mm top manways with davit. Top center mounted 350 kW (475.8 hp), 50 Hz. ABB electric drive with SPX-Flow (Lightnin) gearbox. (4) Lug mounted. Serial #458. Built in 2021. Stored under Nitrogen purge.

Used 200 gallon 304 Stainless Steel Pressure Rated Storage Tote. Manufactured by Ucon AG. Single shell rated 15 psi, top pressure manway. Dome top, cone bottom. 2.5" tri-clamp outlet with integrated butterfly valve. 45" dia x 50" tall, Serial #58092.

Used 350 gallon stainless steel single shell portable tote. Manufactured by Custom Metalcraft. Top boltdown manway, multiple top flanges. 2” outlet. 48” X 42” X 54” H. Serial #10484-91.

Used 528 gal (2000 L) 316L Stainless Steel Jacketed Pressure vessel. Manufactured by Precision Stainless. Internal rated 50 PSIG/FV @300F. 304L Jacket rated 100PSIG@300F. Dish bottom and top. Top manway. (4) Leg mounted. National Board #4818. Serial # 6516-18. Built 1993.

Used 40000 gallon Stainless Steel Refrigerated Vertical Silo. Manufactured by DCI. Stainless Steel Alcove. Horizontal agitator. CIP/Vent/Overflow lines. Spray ball. Thermowell. RTD well. 3"Inlet, 3" outlet. 400 St Ft Coldwall. 150"Dia x 624"H.

Used Flaker 59"W 304 stainless steel enclosed horizontal belt flaker with Pastillator. Manufactured by Steel Belt Systems SRL (SBS) (Italy). serial #RP2 177 12 5. 59"W x 59'L (1.5m wide x 18000mm) cooling length 301 (NICRO 12.1) stainless steel belt. 63' (19250mm) belt length between center of rolls. 30 - 47 rpm belt speed. 38500mm total length of belt. 1mm belt thickness. (3) cooling zones, zone 1 = 5.5m long (3 bar @ 5-9 degrees C), zone 2 = 6m long (3 bar @ 5-9 degrees C), zone 3 = 6.5m long (3 bar @ 5-9 degrees C), (179) plastic cooling nozzles, (2) 800mm wide 304 stainless steel drums, belt is driven by 5.5kw, 3/50/60/400-690/460 volt, 1460/1765 rpm CE IP55 motor via 88.17:1 ratio, 17 rpm reduction gearbox, belt enclosed in a 304 stainless steel housing, pneumatic operated belt tensioner, belt with bakelized fiber scraper blades, (1) 120mm diameter x 1.4m wide 304 stainless steel Roll Drop pastillator for distributing the liquid drops onto the cooling belt, 8mm toothed rotor pitch, type 3 x 1mm, comb material TEKAPEEK, 105 degrees C, driven by 2.2kw, 3/50//60/230-400 /265-460 volt, 1445/1755 rpm CE IP55 motor via 13.91:1 ratio, 104 rpm reduction gearbox. Pastillator with pneumatic operated raise/lower mechanism, belt with pneumatic operated knife discharge with a brass blade, 304 stainless steel water trays, built on controls, Thermo Scientific model MINI-11-101F weight integrator, emergency stop button and pull cord, all mounted on a Galvanized carbon steel frame, approx 20600mm total length of flaker, (1) discharge belt conveyor.

Used 18.1 MMBTU/Hr Hot oil boiler. Manufactured by Heatec. Model VHCI 10010-50-G-(D). Input 22.1 MMBTU/hr. Flow rate 1465 GPM. Transfer media Dowtherm. Heating surface 1521 Sq ft. Design 300PSIG@750F. Outlet media 528F. Pressure Drop 12.9 PSIG. 125HP Blower. Economizer 2.5 MMBTU/hr. 300 PSIG@750F. Heating surface 2324 Sq ft. Pressure Drop 1.34 PSIG. Stack. Contols. Built 2011.

Used Air cooled chiller. Manufactured by Drake. Model VPACT6S6-T4-Z. Serial #D13H1157. Built 2014.

Used 40" x 20" Hastelloy basket centrifuge. Manufactued by Ketema. 50HP motor. Max density 95 Lb/Cu ft. Controls

Used glass lined double cone dryer. Manufactured by Pfaudler. Serial #R479-3807

Used 4000 gallon 316L Stainless Steel Tank. Manufactured by K&E Fabricating. 72"Dia x 204" Straight-side. Dome top, dish bottom. Leg mounted. Built 2014.

Used 4000 gallon 316L Stainless Steel Tank. Manufactured by K&E Fabricating. 72"Dia x 204" Straight-side. Dome top, dish bottom. Leg mounted. Built 2014.

Used 5500 gallon 316L Stainless Steel Tank. Manufactured by K&E Fabricating. 72"Dia x 204" Straight-side. Dome top, dish bottom. Leg mounted. Serial# 632-2. National Board# 4. Built 2014.

Used 5500 gallon 316L Stainless Steel Tank. Manufactured by K&E Fabricating. 72"Dia x 204" Straight-side. Dome top, dish bottom. Leg mounted. Serial# 632-1. National Board# 3. Built 2014.

Used Kelvion Rainey air cooled heat exchanger. Manufactured by Kelvion. Serial #R-10720-1-A. Built 2017

Used FEDS Ring/Flash Dryer system. Manufactured by ThermaJet. Includes Baghouse w/ rotary valve, Cylone w/rotary valve, Air supply blower with HEPA, Exhaust Blower with HEPA, Electrical heater, DSM Hopper w/rotary valve, Product feed screws, Air product manifold with duct work. Built 2006.

Used 50" Stainless Steel Pharma Peeler centrifuge. Manufactured by KMPT. Model HZ1250/2.5ph. 1250mm (50") D basket. 1250 kg/m3 50C. Serial #60000801. Built 2006.

Used 1000 gallon 316L Stainless Steel Reactor. Manufactured by K&E Fabricating. Internal Rated 250PSI/FV@500F. Jacket rated 150PSI @500F. Top entering Lightnin agitator. Dome top. Lug mounted. National Board #2. Serial #602. Built 2014.

Used 1000 gallon 316L Stainless Steel Reactor. Manufactured by Brighton. Internal rated 200PSI/FV@350F. Jacket rated 182PSI@350F. Top entering Pfaudler agitator. Dom top, flat bottom. Leg mounted. National Board #2063. Serial #A5923. Built 1968

Used Stainless Steel Plate evaporator system. Manufactured by APV. Includes (3) schmidt heat exchangers, separator vessel, vacuum pump, (2) centrifugal pumps. Built 2006.

Used 28"W x 13'L Stainless Steel Fluid Bed dryer. Manufactured by Kinergy. 3300 RPM max. Includes Hot air blower, oil heat exchanger, filter, duct work, Cold air blower, filter, duct work (2023), Exhaust blower, cyclone, filter (2023), Spare Parts - replacement coils, springs, oil heat exchanger. Built 2006.

Used 17 Cu Ft stainless Steel Jacketed conical screw Mixer. Manufactured by Nauta. Stand mounted. Controls. Built 1968.