Used- Schutte-Buffalo-Astec Hammermill, Model AHM-20, Carbon Steel. Approximate (2) 48" diameter x 24" wide rotors. Top feed with hopper, bottom discharge. Driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor.

Used- Schutte-Buffalo-Astec Hammermill, Model AHM-20, Carbon Steel. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Serial# 16-086-299260-22-1. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor. Astec serial# 16-086-299260-22-1.

Used- Schutte-Buffalo-Astec Hammermill, Model AHM-20, Carbon Steel. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Serial# 16-086-299260-22-1. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor. Astec serial# 16-086-299260-22-1.

Used- Schutte-Buffalo-Astec Hammermill, Model AHM-20, Carbon Steel. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Serial# 16088HM1. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor. Astec serial# 16088HM1.

Phoenix Equipment is pleased to offer major process machinery from a Used 600,000 TPY wood pellet plant, built in 2017, in Pine Bluff, Arkansas. The offering consists of (4) individual stand-alone lines (20 tons per hour), each consisting of drying island and hammer mill loops. Available equipment from each line starts with 65 MMBTU Gas Burner; Combustion Chamber; Convectec Heater; Soot Blowers; Pre-Dryer (air heated); Hot Baghouse; Tube Dryer (oil heated); Heater Oil Loop; Expansion tank; Pump Skid; Dryer Waste Screws; Chip Drag Conveyor; Dry Distribution Screw; Spreader Transition and Rock Box; (2) Dry Hammer Mills; Exhauster Fans, Duct and Cyclones; Long Term Conditioner Screws

Used- Schutte-Buffalo 15 Series Wood Grinder, Model 15300, Carbon Steel. Rotor approximate 44” diameter x 72” wide with approximate 3” wide x ¾” thick swinging hammers, tip speed 20,700. Top feed, bottom discharge, bottom screen approximate 5040 square inch area, clam shell housing. Driven by a 500hp, 3/60/460 volt, 1785 rpm motor. Mounted on an I beam frame. Serial# 17-12027B.

Used- Schutte-Buffalo 15 Series Wood Grinder, Model 15300, Carbon Steel. Rotor approximate 44” diameter x 72” wide with approximate 3” wide x ¾” thick swinging hammers, tip speed 20,700. Top feed, bottom discharge, bottom screen approximate 5040 square inch area, clam shell housing. Driven by a 500hp, 3/60/460 volt, 1785 rpm motor. Mounted on an I beam frame. Serial# 17-12027A.

Used- Schutte-Buffalo 15 Series Wood Grinder, Model 15300, Carbon Steel. Rotor approximate 44” diameter x 72” wide with approximate 3” wide x ¾” thick swinging hammers, tip speed 20,700. Top feed, bottom discharge, bottom screen approximate 5040 square inch area, clam shell housing. Driven by a 500hp, 3/60/460 volt, 1791 rpm motor. Mounted on an I beam frame. Serial# 1709002D.

Used- Schutte-Buffalo 15 Series Wood Grinder, Model 15300, Carbon Steel. Rotor approximate 44” diameter x 72” wide with approximate 3” wide x ¾” thick swinging hammers, tip speed 20,700. Top feed, bottom discharge, bottom screen approximate 5040 square inch area, clam shell housing. Driven by a 500hp, 3/60/460 volt, 1791 rpm motor. Mounted on an I beam frame. Serial# 1709002C.

Used- Schutte-Buffalo 15 Series Wood Grinder, Model 15300, Carbon Steel. Rotor approximate 44” diameter x 72” wide with approximate 3” wide x ¾” thick swinging hammers, tip speed 20,700. Top feed, bottom discharge, bottom screen approximate 5040 square inch area, clam shell housing. Driven by a 500hp, 3/60/460 volt, 1791 rpm motor. Mounted on an I beam frame. Serial# 1709002B.

Used- Schutte-Buffalo 15 Series Wood Grinder, Model 15300, Carbon Steel. Rotor approximate 44” diameter x 72” wide with approximate 3” wide x ¾” thick swinging hammers, tip speed 20,700. Top feed, bottom discharge, bottom screen approximate 5040 square inch area, clam shell housing. Driven by a 500hp, 3/60/460 volt, 1791 rpm motor. Mounted on an I beam frame. Serial# 1709002A.

Astec Screener, Model 1624V, Carbon Steel. Approximate 72" wide x 24' long, 2 separation. Serial# 154205.

Astec Screener, Model 1624V, Carbon Steel. Approximate 72" wide x 24' long, 2 separation. Serial# 154203.

Astec Rotary Tube Type Indirect Dryer, Model WPD-10829, Carbon Steel. Last used with wood chips removed 5% - 6% moisture from feed material. End feed with hopper and screw feeder, end discharge with hood and a stainless steel auger discharge. Dryer driven by a chain & sprocket with a 60hp motor with a reducer, ratio 43.78 to 1. Includes a control panel with a Siemens Milltronics BW500/L controller. Serial# 15-206-288662-4-1.

Astec Rotary Hot Oil Tube Type Indirect Dryer, Model TD-1060, 13'3" diameter x 68'7" long, Carbon Steel. Last used drying wood from 45% to 10% moisture content. End feed with hopper and screw feeder, end discharge with hood and hot oil inlet & outlet manifold. Dryer driven by a chain & sprocket with a 75hp motor with a reducer, ratio 64.42 to 1. Includes a control panel with a Siemens PLC controller, thrust idler hydraulic pump panel. Serial# 15-206-288662-8-1.

Continental Enclosed Tube Inclined Screw Conveyor, Carbon Steel. Approximate 24" diameter x 28' long with motor and reducer.

Astec Chip Drag Conveyor, Model BTD Drag. 304 Stainless steel housing, plastic paddles, carbon steel chain. Approximate 18" wide x 48' overall length. Driven by a 7.5hp motor with reducer. Serial# 15-206-288662-19-1.

Hammermill Loop System Consisting Of: (2) Schutte-Buffalo-Astec Hammermills, Model AHM-20 Carbon Steel. Each mill has approximate (2) 48" diameter x 24" wide rotors. Top feed with hopper, bottom discharge. Each mill driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Each mounted on a frame. Includes (2) Twin City blowers, Type RBR-SW, size 926, each driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor. (1) Top mounted dry distribution dual screw feeder. Designed to split flow of material to each hammermill, or reverse a screw to send all material to one side and (2) exhauster cyclones.

Used- Schutte-Buffalo-Astec Hammermill, Model AHM-20, Carbon Steel. Approximate 48" diameter x 50" wide rotor. Top feed with hopper, bottom discharge. Driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Mounted on a frame. Includes a Twin City blower, Type RBR-SW, size 926, driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor.

Astec Wood Fuel Conditioner, Carbon Steel. Approximate 12' diameter x 12' straight side. Side access door, (3) off center bottom outlets with (1) discharge screw conveyor. Top mounted agitator with a 50hp motor.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 16" diameter x 24' long with motor and reducer.

Smoot Blower System Consisting Of: (1) Roots positive displacement blower, model 56U-RAI, serial# 1510923284, driven by a 20hp motor. Includes silencer. Mounted on a frame, Smoot serial# 64938-1.

Hot Oil Pump Skid Consisting Of: (3) Blackmer System One Centrifugal Pumps, Model FRM, 316 Stainless Steel. Size 8 X 10-13, approximate 4200 gallons per minute at 110' head at 275 psi at 100 degrees F. Each driven by a 100hp motor, serial# 1108454FM, 1080014FM, 1094376FM. (3) Strainers with miscellaneous piping and valves. (1) Xylem 2 pass carbon steel shell & tube heat exchanger. Shell rated 125 psi at 1600 degrees F., tubes 150 psi at 1375 degrees F. Serial# 284050-03-2, National Board# 315500, built 2019. (1) Skid with a pump, heat exchanger and tank. (1) Expansion tank and a panel.

Astec Gas Burner, Model PB-65U-B-G-0-SF-FD-BB. Rated 65 MMBTU/HR. Job# 006744-015-206. Includes (1) combustion chamber, (1) Lapco ash collector, and (1) Twin City blower, size 270, type RTF-SW. Driven by a 75hp motor, serial# 19-746509-16-1.

Heatec Convectec All Convection Heater, Hot Oil Heater, Job# HI16-062-551. Includes a control panel, expansion tank and (1) Twin City blower, size 917, type RBO-SW. Driven by a 15hp motor, serial# 15-546656-3-1.

Used Stainless Steel Cyclone, Approximate 7' diameter x 40' tall. Includes a bottom rotary valve and (1) Twin City blower, size 929, type RBR-SW. Driven by a 200hp motor, serial# 19-746510-2-1.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 16" diameter x 24' long with motor and reducer.

Astec Hot Baghouse, Model BH-68-12-PP, Carbon Steel. Top bolt on bag section housing, coned bottom discharge section with discharge conveyor. Includes a 250hp blower.

Astec Hot Baghouse, Model BH-68-16-PP-S, Carbon Steel. Top bolt on bag section housing, coned bottom discharge section with discharge conveyor. Serial# 18-003-331776-1-1. Includes a 250hp blower.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 19' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 21'6" long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 13' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 16' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 16' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 21'6" long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 24' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 24' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 24' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 24' long with motor and reducer.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 12" diameter x 24' long with motor and reducer.

Astec Rotary Tube Type Indirect Dryer, Model WPD-10829, Carbon Steel. Last used with wood chips removed 5% - 6% moisture from feed material. End feed with hopper and screw feeder, end discharge with hood and a stainless steel auger discharge. Dryer driven by a chain & sprocket with a 60hp motor with a reducer, ratio 43.78 to 1. Includes a control panel with a Siemens Milltronics BW500/L controller. Serial# 16-086-299260-4-1.

Astec Rotary Hot Oil Tube Type Indirect Dryer, Model TD-1060, Carbon Steel. Last used drying wood from 45% to 10% moisture content. End feed with hopper and screw feeder, end discharge with hood and hot oil inlet & outlet manifold. Dryer driven by a chain & sprocket with a75hp motor with a reducer, ratio 64.42 to 1. Includes a control panel with a Siemens PLC controller, thrust idler hydraulic pump panel. Serial# 16-086-299260-8-1.

Continental Enclosed Tube Inclined Screw Conveyor, Carbon Steel. Approximate 24" diameter x 28' long with motor and reducer.

Hammermill Loop System Consisting Of: (2) Schutte-Buffalo-Astec Hammermills, Model AHM-20 Carbon Steel. Each mill has approximate (2) 48" diameter x 24" wide rotors. Top feed with hopper, bottom discharge. Each mill driven by a 600hp, 3/60/460 volt, 1790 rpm motor. Each mounted on a frame. Includes (2) Twin City blowers, Type RBR-SW, size 926, each driven by a 200hp, 3/60/230/460 volt, 1785 rpm motor. (1) Top mounted dry distribution dual screw feeder. Designed to split flow of material to each hammermill, or reverse a screw to send all material to one side and (2) exhauster cyclones.

Astec Chip Drag Conveyor, Model BTD Drag. 304 Stainless steel housing, plastic paddles, carbon steel chain. Approximate 18" wide x 48' overall length. Driven by a 7.5hp motor with reducer. Serial# 16-087-299328-16-1.

Astec Wood Fuel Conditioner, Carbon Steel. Approximate 12' diameter x 12' straight side. Side access door, (3) off center bottom outlets with (1) discharge screw conveyor. Top mounted agitator with a 50hp motor.

Astec Enclosed Tube Screw Conveyor, Carbon Steel. Approximate 16" diameter x 24' long with motor and reducer.

Smoot Blower System Consisting Of: (1) Roots positive displacement blower, model 56U-RAI, serial# 1605933603, driven by a 20hp motor. Includes silencer. Mounted on a frame, Smoot serial# 72582-001.

Hot Oil Pump Skid Consisting Of: (3) Blackmer System One Centrifugal Pumps, Model FRM, 316 Stainless Steel. Size 8 X 10-13, approximate 4200 gallons per minute at 110' head at 275 psi at 100 degrees F. Each driven by a 100hp motor, serial# 1080015FM, 1108452FM, 1080141FM. (3) Strainers with miscellaneous piping and valves. (1) Xylem 2 pass carbon steel shell & tube heat exchanger. Shell rated 125 psi at 1600 degrees F., tubes 150 psi at 1375 degrees F. Serial# 284050-01-2, National Board# 314910, built 2018. (1) Skid with a pump, heat exchanger and tank. (1) Expansion tank and a panel.

Astec Gas Burner, Model PB-65U-B-G-0-SF-FD-BB. Rated 65 MMBTU/HR. Includes (1) combustion chamber, (1) Lapco ash collector, and (1) Twin City blower, size 270, type RTF-SW. Driven by a 75hp motor, serial# 19-746509-16-1.